Beginners’ Guide to Netgear Router Troubleshooting Lights

September 17, 2020 Annie Mitchell

A Netgear router comes with various LEDs that indicate the status of the connection between your router and the connected devices. They also signify the status of Ethernet, WiFi, Internet, and WPS connections. At times, the LEDs, all of a sudden, start blinking or become off resulting in WiFi connectivity issues. And most of the users don’t even know the reason behind the LED issues. That’s why we have come up with this Netgear router troubleshooting lights guide.

Here, we will highlight a few issues with your Nighthawk router LEDs as well as their fixes. Let’s get started.

Netgear Router Troubleshooting Lights

1. Netgear Router Orange Light

Netgear router orange light is the most common issue faced by users across the globe. In the event that the Netgear internet light is blinking in orange, it indicates that there is a slow internet connection. To fix the Netgear router orange light issue, do the following:

Power-cycle your Netgear WiFi router and modem. All you need to do is simply disconnect your router from the power outlet, wait for a while, and then connect it again to the wall outlet.
Did you check the internet status on your modem? Perhaps you have lost the internet from your ISP.
At times, users see the blinking orange light on Netgear router due to a faulty WiFi connection. In such a case, switch to a wired connection instead of the WiFi one.

If you are still stuck with the Netgear router orange light, get in touch with our experts immediately and get the issue fixed.

2. Netgear Router Internet Light Blinking White

This issue mostly occurs in new Netgear router models, e.g. if you have performed the Netgear Nighthawk AC1900 setup, chances are that you might be seeing this error. The blinking white internet LED indicates that your router is failed to connect to your modem.

In case your Netgear router internet light blinking white, restart your network by following the steps below:

Turn off and disconnect the power adapter of the modem from the wall socket.
Disconnect all the devices that are connected to the network.
Power off your Netgear router as well.
Now, plug in your modem and then turn it on.
After that, power on your router.

Once done, see whether the issue has fixed now.

3. Netgear Router Red Power Light

Here are the troubleshooting steps to resolve the Netgear router red power light error:

Ensure that you are utilizing the power adapter that came in your router’s package.
Power off your router and then turn it on again to see if the power LED becomes green.
If the power LED stays amber, press and hold the Reset button to restore all the default settings on your Netgear router.
Set the Subnet Mask, IP Address, and Default Gateway of your computer to static.

Still seeing the blinking power LED on your Netgear router? Reach out to our highly-knowledgeable technicians anytime.

4. Netgear Router Flashing Blue Light

The blue light shows that your Netgear router is booting up. However, if the Netgear router flashing blue light for longer, then that is something you need to think upon. But you don’t need to worry as we have also covered the fix for this issue in our Netgear router troubleshooting lights guide.

To fix the blue light error, here are the do-follow steps:

Make sure that there is no hardware damage related to your Netgear router.
Let your router boot up properly.
Afterward, the device will request a DHCP lease and attempt to obtain an IP.
In case the IP is obtained, the LED will turn into orange.
If it doesn’t become orange, change the DHCP settings of your router via the Netgear Nighthawk app.

So, these were some of the common issues with the Netgear router LEDs. Hopefully, you are now able to fix them.

How to Enable/Disable LED Lights on Netgear Router?

In our Netgear router troubleshooting lights guide, we have also covered the steps to enable/disable the LED lights on your Netgear Nighthawk router. Let’s have a look at them:

Connect your Netgear router to the modem through a cable.
Load up Google Chrome on your PC. You can also choose Firefox or Safari.
Go to the Netgear genie setup page.
Click on the LED Control Settings option.
Choose either Enable or Disable blinking on Wireless LED, LAN LED, USB LED, and Internet LED when data traffic is determined.
Disable all LEDs except the Power LED – This option will turn off all the LEDs on your Netgear router excluding the Power LED.

And with this step, our Netgear router troubleshooting lights guide completes. In case of any difficulty, contact our experts.